Has your ideal logic boiler broken down and you have error codes showing up but you do not know what they mean?
Related content:
Boiler Repair Service Fife and Edinburgh
Should you need professional help with your broken boiler, then simply use one of our enquiry forms and we will connect you with the best heating engineers local to you.
Ideal Logic Boiler Error Codes
Fault Code | System Behaviour |
---|---|
C0 | BCC Activation Fault |
C2 | BCC Fault |
F1 | Low Water Pressure |
F2 | Flame Loss |
F3 | Fan Fault |
F4 | Flow Thermistor |
F5 | Return Thermistor |
F6 | Outside Sensor Failure |
F7 | Low Mains Voltage |
F9 | Unconfigured PCB |
L1 | Flow Temperature Overheat or No Water Flow |
L2 | Flame Loss |
L5 | 5 Boiler Resets in 15 minutes |
L6 | False Flame Lockout |
Ideal Logic Boiler Error Description
Fault Description | Reason |
---|---|
Overheat Lockout | Go to Frame 82 Overheat Lockout |
Ignition Lockout | Go to Frame 83 Ignition Lockout |
Flame Loss | Go to Frame 84 Flame Loss |
Thermal Fuse Lockout | Reset Boiler |
Too Many Resets | 5 Resets within 15 minutes Turn power off and on |
Flame on before Gas Valve on | Go to Frame 86 Flame On before Gas Valve On |
Flow Thermistor Fault | Go to Frame 87 Flow Thermistor Fault |
outside sensor fault | Go to Frame 87 Flow Thermistor Fault |
Return Thermistor Fault | Go to Frame 89 Return Thermistor Fault |
Fan Fault | Go to Frame 90 Fan Fault |
PCB Replaced Incorrectly | Ensure BCC fitted correctly Ensure correct BCC fitted |
Low Mains Voltage | Less than 160V to boiler Check voltage at boiler mains in Check if local generator 10V Contact Electricity Provider |
Low Water Pressure | Fill System to 1 Bar Bleed Radiators Refill System to 1 Bar |
Flow/Return Reversed | Check if Flow Thermistor correctly clipped to pipe Replace Flow Thermistor |
No Water Flow | Go to Frame 92 No Water Flow Fault |
PCB Replaced | Reset boiler by pressing r |
No Connection to Primary PCB | Unblock Pump |
Pump Rotor Blocked If fault persists | Go to Frame 93 No Connection to Primary PCB |
No CH but DHW OK | Go to Frame 94 No CH but DHW OK |
No DHW but CH OK | Go to Frame 95 No DHW but CH OK |
Blank Display | Go to Frame 96 Blank Display |
Flow Temp Cannot Be Increased To 80 | Ensure Flow Temperature is not limited within Installer Mode (see Frame 37 |
Pump Runs During Night | Ensure System Frost Protection Temperature Setpoint is not set too high (see Frame 40) |
Has PCB just been replaced? | Reset Boiler |
Are the Boiler and CH/DHW system filled with waterand are all Isolation Valves and Radiator Valves open? | Fill and vent the system and open allIsolation Valves, then Reset the Boiler |
Is the Flow/Return Differential across the boiler in excess of 30c | Check the Flow and Return Thermistors(refer to Frames 87 & 89) |
Check that the Pump is rotating freely. | Replace the Pump, then Reset the Boiler |
If the Boiler is Reset, does it Ignite for a short time and then extinguish | check the Detection Electrode and associated Harness for continuity, visual condition and position (refer to Frame 59). Check if the Condensate Pipe is Blocked |
is the gas pressure avaliable at the boiler > 18mBar | Check Gas Supply and rectify fault |
is 215Vdc avaliable at the gas valve during ignition | Check wiring from Gas Valve to PCB and replace if necessary, otherwise replace the main PCB |
unplug the gas valve is the resistance between the pins between 1Kw and 10KW | Replace Gas Valve |
Ideal Logic Boiler Error Codes
Listed below are some error codes that could appear on your Ideal boiler.
Fault Code | System Behaviour |
---|---|
0 | The boiler is in standby mode awaiting either a central heating call or hot water demand |
C | The boiler has a call for central heating but the appliance has reached the desired temperature set on the boiler |
D | The boiler has a call for hot water but the appliance has reached the desired temperature set on the boiler |
C | The boiler is operating in central heating mode |
d | The boiler is operating in hot water mode |
F | The boiler is operating in frost mode |
Boiler Repair Quote
If you are having problems with your ideal logic boiler and have the above error codes appearing then give us a call today.
We offer a 24/7 emergency call out service to cater for our customers needs.
Get in touch with us today.